ViewSonic Pro8100 Instrukcja Użytkownika

User’s ManualPrecision by ViewSonic®Home Theater ProjectorFRNESPENG

6Chapter 2: InstallationPower connection1. Remove the projector lens cap.2. Plug the attached power cord into the AC power socket of this projector.3.

ENGInstallation7A. Using Home Theater System as hubThis setup is recommended if a highly sophisticated home theater system is available. This setup of

8B. Using Projector as hubThis setup is recommended for low to mid range home theater system. When changing input source, both projector and home thea

ENGInstallation9D. RS232 ConnectionThe illustration shows the connection to a home appliances control device. ViewSonic Pro8100’s RS232 command code t

10Adjusting the Projector Lens Position1. Press the Lens Shift button.2. Use four directional buttons to adjust the lens position.The adjustable proje

ENGInstallation11Adjusting Projection Image SizeRefer to the graphic and table below to determine the screen size and projection distance.40"80&q

12Chapter 3: Remote Control direct accessPowerPower button to turn on or off the projector.Power ONPress on the remote control/top panel to turn on

ENGRemote Control direct access13Zoom and FocusMotorized zoom and focus adjust.Press on the remote control to browse through zoom and focus adjust o

14Aspect RatioSelections of screen proportion.Press on the remote control to browse through available aspect ratio options.Normal: Browse through st

ENGRemote Control direct access15PCS (Precision Color System)PCS consists of advanced color enhancement functions such as flesh tone correction, edge

iCompliance InformationFCC StatementThis device complies with part 15 of FCC Rules. Operation is subject to the following two condi-tions: (1) this de

16Black LevelBlack level defines the brightness levels at the darkest visual image point. Higher black level removes color noise at darker grayscales

ENGRemote Control direct access17Daylight SensorEnable daylight sensor to automatically adjust the best viewing condition based on ambient light condi

18Direct Input KeysDirect input source switching without browsing through entire input selections.Press once on the remote control will show source st

ENGRemote Control direct access19

20Chapter 4: ADVANCED OPERATION (OSD Menu)1. Main MenuPress to enter the main menu (Fig. 1-2).Fig. 1-1OSD Navigation KeysSETUPSTATUSH1H2C1C2A1S1P116

ENGADVANCED OPERATION212-1. Picture Sub-MenuUse ▲ and ▼to navigate the Picture Sub-Menu (Fig. 2-1) Selections:Press to confirm the Sub-Menu selectio

222-1-2 Color Temperature Sub-MenuUse ▲ and ▼ to navigate the Color Temperature Sub-Menu Selections.Press to confirm the Sub-Menu selection.Press

ENGADVANCED OPERATION232-1-4 Aspect RatioThese functions can only be utilized in video inputs.Use ▲ and ▼ to navigate the Image Adjust Sub-Menu Select

242-1-6 Geometry AdjustAdjust image geometry distortion caused by improper placement of projector electronically. Note: For best video performance, it

ENGADVANCED OPERATION252-2-1 Picture ModeViewSonic customized presets for various viewing pleasures.Use ▲ and ▼ to navigate the image Mode (Fig. 2-2-1

ENGCompliance InformationiiDeclaration of RoHS ComplianceThis product has been designed and manufactured in compliance with Directive 2002/95/EC of th

262-2-3 HQVSelections of HQV (Hollywood Quality Video) for further details enhancements, film detecting modes, and luminance level adjustments.Use ▲ a

ENGADVANCED OPERATION272-2-4 Noise ReductionHQV technology reduces the irrelevant or noise data (Minimum loss of good data) from signal and creates be

282-2-5 Color SpaceSelect the correct color spacing for the given input video format. Wrong selection may result in abnormal color performance. Select

ENGADVANCED OPERATION292-3-1 Projector SettingsProjector Setting selectionsUse ▲ and ▼ to navigate Selections of Projector Settings Sub-Menu (Fig. 2-3

302-3-2 OSDOSD locationUse ▲ and ▼ to navigate Selections of Projector Settings Sub-Menu (Fig. 2-3-1)Press to confirm the Sub-Menu selection.Press

ENGADVANCED OPERATION312-3-4 TimersTimer settingsUse ▲ and ▼ to navigate the Timers Sub-Menu (Fig. 2-3-4) Selections.Press to confirm the Sub-Menu s

322-3-6 Auto IrisAutomatically control the portion of projected light to increase contrast and transition speedUse ▲ and ▼ to navigate Selections of A

ENGADVANCED OPERATION332-4-1 PCSPCS image managementUse ▲ and ▼ to navigate Selections of PCS Sub-Menu (Fig. 2-4-1)Press to confirm the Sub-Menu sel

342-4-3 Flesh toneSkin tone correctionUse ▲ and ▼ to navigate Selections of Flesh tone Sub-Menu (Fig. 2-4-3) Selections.Press to confirm the Sub-Men

ENGADVANCED OPERATION352-4-5 Gamma CorrectionGamma selections and custom adjustments.Use ▲ and ▼ to navigate Selections of Gamma Correction Sub-Menu (

Compliance Information...iFCC StatementFor CanadaCE Conformity for European CountriesFollowing information is only for EU-member statesImporta

36COLOR 500 100CYANENHANCEHUE 500 100Cyan color EnhancementHue – Press ► for a more bluish or ◄ for greenish toneColor – Press ► for richer

ENGADVANCED OPERATION372-5-1 Custom Color TemperatureCustomize color temperature adjustment. This defines color temperature in white balance and offse

382-5-2 SaveSaving Changed ItemsUse ▲ and ▼ to navigate the Saving (Fig. 2-5-2) Selections.Press to confirm the Sub-Menu selection.Press to go to

ENGADVANCED OPERATION392-5-4 ResetResets of ViewSonic defaultsUse ▲ and ▼ to navigate the Reset (Fig. 2-5-4) Selections.Press to confirm the Sub-Men

40AUTODaylight sensor status: Indication if daylight sensor is active.Auto: Daylight sensor is in automatic mode.Manual: Manually select daylight sens

ENGADVANCED OPERATION41NORMALSystem temperature status, display if system is operating under ideal temperature:Normal – System under ideal operating t

42Chapter 5: Making and Recalling the User AdjustmentsMaking Adjustments1-1. User Picture Mode AdjustmentsUser Picture Mode includes the following adj

ENGMaking and Recalling the User Adjustments431-3. User PCS AdjustmentsUser PCS includes the following adjustments:•Flesh Tone •Edge Enhancement •Gamm

442-2 Recalling the User PCS AdjustmentsPerform adjustments:Fig. 2-2 PCS SelectPress the “PCS” button on the remote control.Browse through the PCS Sel

ENGMaking and Recalling the User Adjustments45

ENGIntroduction1Chapter 1: IntroductionProjector FeaturesThe projector integrates high-performance optical engine projection and a user-friendly desig

46AppendixMaintenanceThe projector needs proper maintenance. You should keep the lens clean as dust, dirt or spots will project on the screen and dimi

ENGAppendix47Replacing the LampProjector lamps have a finite life. Replace the lamp when:• A warning message “Lamp is approaching the end of its usef

48TroubleshootingIf you think something is wrong, check the followings before contacting customer service.If This Happens CheckNo power* Is the power

ENGAppendix49Others1280 x 720 60 Hz 45.1 kHz1280 x 800 60 Hz 49.7 kHz1280 x 800 75 Hz 62.8 kHz1280 x 800 85 Hz 71.6 kHz1360 x 768 60 Hz 47.7 kHz1400 x

50LED Indicator MessagePower LED Status LED IndicatesBlinking in Green Off Standby modeGreen Green Warming upGreen Off Projector ON.Green Blinking in

ENGAppendix51RS232 command code1. Protocol Setting2. Power ON/OFF commandCommand Send String (HEX)Power ON BE EF 10 05 00 C6 FF 11 11 01 00 01 00Power

524.2 Key-Pad & IR command 2Command Send String (HEX)Aspect RatioNormal BE EF 02 06 00 8A DF 63 00 00 00 00 00Anamorphic 1 BE EF 02 06 00 3D DE 64

ENGAppendix53Command Function Name Description0x87 Power On Discrete Power On.¹Power On/Off Toggle Power On/Off.²0xA1 Power Off Discrete Power Off0x9E

54Limited WarrantyVIEWSONIC® PROJECTORWhat the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, u

ENGAppendix553. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic. 4. Fo

2Projector Overview(3)(6)(5)(5)(4) (11)(12)(7) (8) (9) (10)(2) (1)(13)(14)1. Control panel2. LED indicator3. Air inlet grille4. Front IR remote contro

ENGIntroduction3Connection ports(1) (2) (3) (4) (5) (6) (7)(8) (9) (10) (11)1. RS-232 terminal When operating the projector via a computer, connect th

44. PCSSelection of PCS mode. PCS On: Use ViewSonic default PCS settings. USER: Use user defined PCS settings. PCS Off: Turn off all PCS settings. 5.

ENGInstallation5Installing the Batteries1. Open the battery cover in the direction shown.2. Install batteries as indicated by the diagram inside the c